Bathroom waterproof construction supervision need to pay attention to what
There are many kinds of materials used for bathroom waterproofing at present, basically the waterproof effect is good. But you should pay attention to the specific construction details.
Rocca bathroom cabinet    Geberit water tank    Hengfu Ceramics
1, the bathroom floor to do leveling. If you want to change the floor tiles of the bathroom, you must first level the floor with cement mortar after the original floor tiles are cut, and then do the waterproof treatment. This will prevent leakage of the waterproof coating due to uneven thickness.
2, seams to brush in place. The seams between the bathroom wall and the seams between the upper and lower water pipes and the ground are the most prone to problems. During construction, you must urge the workers to handle these corners. All waterproof paint must be applied in place.
3, wall treatment is also very important. In the general bathroom waterproofing treatment, a waterproof coating of about 30 cm in height is also required on the wall to prevent water accumulation from passing through the wall. However, if the wall of the bathroom is a non-load-bearing light wall, the entire wall should be covered with a waterproof coating. If your home uses a two-seater shower screen, the two walls that are associated with it must be fully painted. If your home uses a bathtub, the height of the waterproof coating should be higher than the upper edge of the bathtub.
4, waterproof experiment must do. After the construction of the bathroom was completed, all the water in the bathroom was blocked, and a 25 cm high “can†was built at the entrance. Then, 20 cm of water was poured into the bathroom. After 24 hours, you can check whether there is any leakage around the wall and the ground. This 24-hour waterproof test is the key to ensuring the quality of the bathroom waterproofing project. You must do it.
5, keep the water open. All sewers in the bathroom, including floor drains, sanitary ware plumbing, etc., should be kept open. In this way, we can fundamentally avoid the occurrence of the "flooded seven army" tragedy.
There are a wide variety of wall and floor tiles in the market, with rich colors. You should pay attention when choosing:
First, according to their own preferences and field layout, from the floor tiles brand, specifications, color selection.
Second, to buy wall tiles, we must pay attention to its resistance to cracking and strength, good quality tiles, low water absorption, good resistance to cracking, when purchasing can be followed by a drop of water, see the speed of water absorption, water absorption Slower is better.
Third, to see whether the surface is smooth, with or without uneven pinholes. When you buy, you can click and listen to the sound. The more brittle the sound, the higher the density and the better the hardness.
Fourth, look at the color, select the tiles on the outside from the 0.8m to see the same color pattern.
Fifth, the size of the standard, uniform size, uniform thickness, when selected in a box of random draw a few to compete. See if it is the same.
6. When consumers purchase tiles, they must pay attention to whether they indicate signs or characters that meet the national green health standards, and do not buy three tiles. Experts suggest buying tiles in three steps:
The first step: determine the space used by the tiles. Are you buying a tile that is used in the kitchen, bathroom or living room? After you have decided on the most basic conditions, make your choice.
The second step: According to the technical indicators to determine whether the tiles meet the requirements. The degree of fit (also called wear resistance) indicates the extent to which the tiles are prone to wear: Tiles with a 1 degree rating have the lowest wear resistance and are generally used for display, walls, and activities where there are few; II-degree tiles are mainly used in bathrooms. In areas with no hard friction, such as bedrooms, etc.; III-degree tiles are suitable for places where people move frequently, such as living rooms, kitchens, etc.; IV-degree tiles have high wear resistance and are suitable for use in halls, corridors, and public places of luxury houses; V In general, it has super wear resistance and is used in non-domestic environments such as airports and stations.
The third step: Consult the performance of ceramic tiles such as acid and alkali resistance so as to select the right detergent and prevent the glaze from being contaminated.
Construction Acceptance Bathroom Tiles Coatings Bathroom Spaces Residential Cement Living Room Wall Color Kitchen Doors Bathroom Tiles Bathroom Doors Bathroom Tiles Colors Bathroom Doors Dimensions Bathroom Dimensions Public Bathrooms Toilets Waterproof Bathroom Tiles Bedroom Tiles Specifications Kitchen Tiles ld Tiles
Cold Rolled Steel Coil,Black Cold Rolled Steel Coil,Steel Coil
Prepainted Steel Coil/sheet/strip Roofing Sheet Co,Ltd , http://www.nssteelcoil.com