Tile purchase and acceptance
With the increase in personal income and appreciation of taste, more and more families choose to apply tiles during the renovation.
So how do you choose ceramic tiles to distinguish tiles?
>>>Links: Kitchen Bricks Have Doorways 5 Teach You
one look
Mainly to see whether there are black spots on the surface of the tile, bubbles, pinholes, cracks, with or without scratches, stains, missing edges, missing corners, vitrified tiles should also pay attention to whether there is leakage, leakage grinding and other defects. Check the bottom embryo trademark mark, the regular manufacturer's product bottom embryo has a clear product trademark mark, if not or is particularly vague, it is recommended carefully selected!
Second, you
That is, the weight of the ceramic tile, the feel of the ceramic tile, the quality of the same specification product, and the high density brick feel are relatively heavy. On the contrary, the quality of the product is lighter.
Third, listen
Identify the quality of the tiles by listening to the sound by tapping on the tiles:
Tap method:
1) Wall tiles or small size tiles
Generally, one hand separates with five fingers, drags up the tile, and taps the face of the tile with the other hand. If the emitted sound is metallic, the quality of the tile is better.
2) Floor tiles (glass tiles or antique tiles used in the living room and other floors)
With a tiled hand on one side, tapping the middle of the tile with the other hand's palm, if the sound is thick and the echo is long, such as tapping the sound of a bronze bell, the porcelain is highly porcelain and wear-resistant. Strong, high flexural strength, low water absorption, less susceptible to contamination, if the sound is turbid, there is no echo, then the degree of porcelain is low (even cracks), the ceramic body of the tile is not fully calcined, the wear resistance is poor, and the flexural strength is low The water absorption rate will also be higher, and such vitrified tiles are highly susceptible to contamination.
Fourth, fight
The same specifications and models of the product can be randomly taken out of the four, for patching, through this step you can check the tile size, flatness, straight angle and other aspects of the three issues.
(1) Check the size of the tiles. Take two pieces of the same model to the horizontal surface. Use the back of the two hands to slide back and forth along the edge of the tile. If there is no obvious lag when passing through the tiles, The feeling of the hand indicates that the size of the tile is better and the error is small. The smaller the tile size error, the better the tile effect will be! On the contrary, if there are obvious feelings of hand-stopping tiles, indicating that the tile size error is larger, it will affect the effect of paving!
(2) Check the flatness of the tiles. Two or four tiles of the same type are tiled on the plane with the same lines and slide back and forth by hand on the tiles. If there are no obvious seams through the joints of the tiles. The sense of height indicates that the flatness of the tiles is good. On the contrary, it shows that the flatness of the tiles is poor, which will affect the overall effect of the tiles. If the floor tiles are poor in flatness, serious situations will trip people! So this should attract attention.
(3) Tiles with right angles Nowadays, tiles are mostly rectangular, and each corner of the tile is a right angle. If the straight angle is poor, it will also affect the effect of tile paving. Take four pieces of the same type of brick. For splicing, if there are four tiles that cannot be tightly seamed, there is always a gap between one or two seams, indicating that the straightness of the tiles is not particularly good.
Fifth, try
If the problem of non-slip floor tiles is concerned, the material is mainly divided into two types: vitrified and glazed. Now, for the non-slip problem of tiles, now everyone's practice is to add water to the tiles, and then step on them. To see if it is slippery, this practice is not entirely appropriate, because some tiles, especially vitrified tiles, will feel more involved after adding water. This principle is somewhat similar to adding water between the glass if you want to It was difficult to lift it, because it squeezed out the air in the middle and made the brick and the upper contact more closely, so it felt more involved, and some glass tiles felt slippery when not adding water. It is better to try both water and not water.
Buy tiles, the purchase process is not over yet? When dozens of boxes of tiles are sent to home, how can they be checked to prevent JS fraud?
>>> Links: Pay attention to these points when choosing tiles
1, check the outer packaging of tiles
1) Carefully check whether the relevant label on the product packaging box is clear, including the product's brand, trademark, model number, color number, specifications, production batch number or production date, grade, etc.
2) Another important point is to check whether the telephone number of the packing box is accurate. Now, some ceramic tiles with poor quality have not left a complete manufacturer address or telephone on the packing box. The "*** Industrial Zone" like this does not say Which province, which city, the phone is to leave a mobile phone number or phone number without an area code.
2. Check if the delivery product matches the order
1) Check whether each type of tile is the same as the one on the order form;
2) Check whether each type of product delivered is the same as when looking at the product;
3) Check whether the brand name of each tile's embryo body tile is correct and prevent businesses from stealing! There are a lot of tiles that are similar in color, but the brand will be different and the quality may be very different, so you need to pay more attention!
4) Check if there is any missing delivery item!
3, check the number of tiles.
Carefully check the number of tiles, pay attention to the number of tiles and the conversion between tiles.
Now when you buy tiles, you usually calculate them in square meters. When you check, you check the number of tablets. How do you know that the number of merchants is not less? In fact, the method is very simple:
1) Know the area, how to calculate the number of pieces, pay attention to the unity of the unit:
Total number of tiles = tile area (
Tiles to buy glass home decoration flat meters decoration decoration living room glass brick glass door antique tiles specifications
Cylinder,TABLE TOP GAS STOVE Co., Ltd. , http://www.nscylinder.com