Self-priming centrifugal pump has the advantages of strong sewage discharge capacity, high efficiency and energy saving, good self-priming performance, etc. These types of products are suitable for urban environmental protection, construction, fire fighting, chemical, pharmaceutical, dye printing and dyeing, brewing, electric power, electroplating, Paper, oil, mining, equipment cooling, unloading oil tanker and other fields, but as its use continues to increase, self-priming centrifugal pump exposure problems and the use of fault is gradually revealed. So self-priming centrifugal pump failure what? What are the corresponding solutions? Self-priming centrifugal pump failure analysis and solutions 1, Self-priming centrifugal pump body heat failure Analysis: lack of oil, or oil circulation is poor; poor quality lubricants, impurities rust bearings, wear and rotation is not flexible; solution Methods: replacement of qualified lubricants and clean up bearing impurities, adjust the bearing clearance; 2, self-priming centrifugal pump is not on the amount of Failure Analysis: inadequate irrigation pump; pump steering is wrong; pump speed is too low; , The bottom valve is not working Solution: re-irrigation pump; check the direction of rotation; check speed, increase speed; check the motor and power supply; check the filter to eliminate debris; 3, the pump can not start or start the load Large Fault Analysis: Power is not normal; pump stuck; packing pressed too tight; outlet valve is not closed; balance pipe is not smooth; solution: check the power and prime mover situation; hand disk coupling inspection, disintegration inspection, Partial failure; close the discharge valve, restart; everything can not be perfect, their existence more or less have some defects or deficiencies. This is not God's mischief. These inadequacies give us room for growth and progress so that we can continuously improve and progress with the needs of society and the market. Like the self-priming centrifugal pumps, the faults that may occur at work include: A lot, but as long as we find a suitable solution, the same can play a self-priming centrifugal pump maximum value.
Kylin Chemicals Co Ltd has been focusing on R&D, manufacturing and supply of Silicone based high performance surfactants for over 15 years. Our high performance Silicone surfactants and novel technologies are marketed under the trade name KylinSil. KylinSil provides effective solutions to meet our customers' needs in the industries of paints & coatings, leather, water treatment and agrochemicals, etc. We have a professional team of highly qualified, trained and experienced engineers, who are always ready to serve you at product selection, effectiveness evaluation, product optimization till fully best matching your particular application needs.
KylinSil has a broad range of Silicone surfactants products, which are similar as Dow Corning 190, Xiameter OFX-0190, Dow Corning Q2-5211, Dow Corning 57, Perenol S-83 UV, Xiameter OFX-3667, CoatOSil 1160, CoatOSil 1211, CoatOSil 2812, CoatOSil 7001, CoatOSil 7602, CoatOSil 7608, CoatOSil 77, BYK 302, BYK 306, BYK 307, BYK 331, BYK 333, BYK 346, BYK 348, BYK 378, BYK 3510, Tego Wet KL 245, Tego Wet 250, Tego Wet 270, Tego Glide B1484, Tego Glide 410, Tego Glide 432, Tego Glide 450, etc.
Other Names:
Silicone Leveling Agent; Silicone Leveling Additive; Silicone Flow Agent; Flow and Leveling Additive for leather; Flow and Leveling Additive for Coating and Paint; Flow and Leveling Additive for PU; Silicone Antifoam; Silicone Defoamer; Substrate Wetting Additive; Silicone Flow And Leveling Agent; Silicone Flatting Agent; Polyether modified polydimethylsiloxane; Organosilicone Leveling Agent; Organosilicone Antifoam; Organosilicone Defoamer.
Silicone Flow and Leveling Agent
Silicone Flow And Leveling Agent,Silicone Leveling Agent,Silicone Surfactants Leveling
Kylin Chemicals Co., Ltd. , http://www.kylin-chemicals.com