Japan oil research A / AR series pumps

Oil Research A16 Series Working Pressure: 100 Plunger Diameter: 25MM (mm) Plunger Number: 24 Impeller Structure: Semi-Open Impeller Number of Turbines: Multistage Shaft Position: Horizontal Material: Cast Iron Weight: 55 Variable piston pump Flow rate: (m3 / h) Speed: up to 1800 (r / m) Minimum 600 (r / m) Brand: YUKEN / Yan research Drive: Hydraulic Features: High efficiency, At 1800 r / min the volumetric efficiency is more than 98% and the total volume is more than 90%, with the highest efficiency. Energy-efficient: Input power can be saved because of the high total efficiency and good interception characteristics. Low noise: A16-type pump noise less than 57.3dB Less heat: Because of small power loss, can reduce the oil temperature, thus reducing the capacity of the mailbox. Precautions for use: 1, pump installation: When installing the pump, the filling port position should be up. 2, Shaft alignment: Use flexible coupling whenever possible to avoid any stress due to bending or thrust. The maximum allowable error of different axes is less than 0.1MM, allowing the maximum error of less than 0.2 degrees. 3, suction pressure: pump inlet pressure allowed between -16.7 +50 kpa. The suction pipe diameter should be the same as the pipe diameter specified. Pump inlet height from the mailbox must be less than 1m. 4, Piping Information: When using the steel pipe at the outlet of suction inlet, noise may be generated due to extra load on the pump by the pipe. In order to avoid extra load, please use like absurd hose. 5, suction pipe: If the pump is installed above the surface, the suction pipe and the suction pipe filter should not be higher than the pump interface to prevent air from entering the suction pipe. 6, involving oil pipe: installed in accordance with the following table with a pipeline, and should ensure that the pressure within the pump cavity to maintain the normal pressure of less than 0.1mpa, the impact pressure is less than 0.5mpa. Piping length of less than 1m, to be installed separately Do not confluence with the return pipe, pipe end submerged in oil. 7, the exhaust: In order to avoid the pump housing and piping mixed with air caused by vibration, it is necessary to deflate, this is recommended to use exhaust valve exhaust pipe. 8. Startup Note: Before starting for the first time, clean hydraulic fluid is injected through the fuel filler opening (refer to the book). To avoid air blockage during the first start-up, adjust the hydraulic circuit so that the oil from the pump returns directly to the tank , Or the use of directional control valve actuator in the no-load operation. 9, pressure, flow adjustment: At the factory, the pump to adjust the maximum amount of fuel and minimum pressure. According to the work flow and pressure regulation. Pressure regulation: Turn the adjustment screw clockwise to increase the pressure. Adjustment screw 1 Turn the appropriate adjustment reference book, be sure to tighten the screw after adjustment. Flow adjustment: turn clockwise to adjust the screw, reducing the flow. Pump accessories Japan's Yuken YUKEN full range of hydraulic components YUKEN high pressure piston pump YUKEN piston pump maintenance YUKEN plunger pump accessories mainly engaged in the following products: Japan YUKEN, NACHI, TOKIMEC, DAIKIN; the United States VICKERS, PARKER; Germany Rexroth Rexroth, Taiwan Kaijia KCL, Sumitomo Japan Sumitomo QT internal gear pump YUKEN: A series variable displacement piston pump A10, A16, A22, A37, A56, A70, A90, A145 A10-FR -01-CK-10 A10-LR-01-BK-10 A10-LR-01-BK-10 A10-LR-01- 10 A16-LR-01-BK-32 A16-LR-01-BK-32 A16-FR-01-BK-32 A16-FR- 01-HK-32 A16-FR-01-CSK-32 A16-FR-01-BSK-32 A16-FR-01-HSK-32 A16-LR-01- A16-LR-01-HSK-32 A22-FR-01-CK-32 A22-FR-01-BK-32 A22-FR- -BK-32 A22-FR-01-CSK-32 A22-FR-01-BSK-32 A22-LR-01-CSK-32 A22-LR-01-BSK-32 A37-FR-04-HKA-32366 A37 -FR-01-BK-32 A37-LR-01-BK-32 A37-LR-01-BK-32 A37-LR- CSK-32 A37-FR-01-BSK-32 A37- FR-01-HSK-32 A37-FR-01-CK-32 A37-LR-01-CSK-32 A37-LR-01-BSK-32 A37-LR-01-HSK-32 A37-FR-01-BK -32 A37-FR-01-HK-32 A37-LR-01-BK-32 A37-LR-01-BK-32 A37-LR- -01-BSK-32 A37-LR-01-HSK-32 A37-LR-01-CSK-32 A37-LR- 32 A56-LR-01-BK-32 A56-LR-01-BK-32 A56-FR-01-BK-32 A56-LR- 01-CSK-32 A56-LR-01-BSK-32 A56-LR-01-BSK-32 A56-LR-01-HSK-32 A56-LR- A70-LR-01-A-60 A70-LR-01-A-60 A70-LR-01-A-60 A70-LR-01- -BS-60 A90-FR-01-HS-60 A70-LR-01-HS-60 A90-FR-01-KS-60 A90-FR-01- LR-01-KS-60 A90-LR-01-KS-60 A90-LR-01-KS-60 A90- CS-60 A145-LR-01-BS-60 A145-FR-01-BS-60 A145-LR-01- AR Series Piston Pump YUKEN: AR Variable Piston: AR16, AR22; YUKEN: AR Variable Piston: AR16-FR01C-20 YUKEN: AR Variable Piston : AR22-FR0 AR16-FR01B-20 YUKEN: AR Variable Piston: AR22-FR01B-20 Features: 1, small and lightweight; with a small lightweight pump body design, AR16 is smaller than the A16 type The AR16 quality lighter than the A16 2, low noise; sub-ah semi-cylindrical inclined plate bearings, reducing vibration and noise. And to achieve a compact. 3, high reliability; AR series of the main built-in parts and A16 and A22 with rich practical results universal, reliability out

Gold Paper

SUNPLUS Gold Paper is made with premium aluminum oxide grains, high quality latex paper and strong resin. Its special stearate coating is designed to prevent clogging and reduce dust problem. It is very well suited for high speed sanding in a wide range of applications.

Gold Paper,Gold Sand Paper,Gold Sandpaper,Gold Paper Sandpaper

GUANGZHOU SUNPLUS TECHNOLOGY CO.,LTD , https://www.sunplussandpaper.com